Fit the tube end of each one over the nipple of the bracket that you mounted to the fender frame in Step 2. M-20201-MA. of torque. Estimated delivery times for Standard Shipping: For full shipping details please view our Shipping Policy, Lionhart LH-Five High Performance A/S Radial Tire (Available in Multiple Sizes), Mickey Thompson Street Comp Tire (Available in Multiple Sizes), Valve Stem-Mounted TPMS Sensor (15-21 All), Valve Stem-Mounted TPMS Sensor (10-14 All), SpeedForm Mach 1 Chin Spoiler (99-04 GT, V6; 99-01 Cobra), Modern Billet GT350/GT350R Style Red Push Start/Stop Button (15-17 All), NITTO NT555 G2 Ultra High Performance Tire (Available in Multiple Sizes). With the hood propped up in the open position, remove both left and right 13mm nut from the upper hood hinge stud. Head of screw will be flush with bracket. Using the 13 mm socket, torque the nuts to 23 Nm. The install is pretty easy but boy its a PITA when you have to torque under the cowl where the wipers are. FORD, FORD MUSTANG, MUSTANG GT, SVT COBRA, MACH 1 MUSTANG, SHELBY GT 500, COBRA R, BULLITT MUSTANG, SN95, S197, V6 MUSTANG, FOX BODY MUSTANG, AND 5.0 MUSTANG ARE REGISTERED TRADEMARKS OF FORD MOTOR COMPANY. Free Shipping Offers are for Standard Ground Delivery service and are only valid for shipping addresses within the 48 Contiguous United States. Read and understand instructions before starting installation.Issues may arise when installing on aftermarket hoods.Installation of this strut kit may cause the rear of hood to lift slightly when in the closed position.Light weight hoods may bow just forward of the strut mounting point.Heavier aftermarket hoods will not be properly supported by the gas struts. 6. Remove the bolt most forward (nearest the front of the car). 2. Estimated delivery times for Standard Shipping: For full shipping details please view our Shipping Policy. I have the american Muscle MMD hood struts about to install. FORD PERFORMANCE PARTS ... 3. Note: Perform the following steps on one side of the hood at a time. Decent! Remove the exposed fender bolts immediately forward of the hood hinge (one on each side). Insert the metal bushing into isolator from the bottom side, as shown below. The rod may need to be rotated to fit properly Your hood will lift and hold firmly at the raised position - no wind or bumping will knock your hood down on your head. Discussion Starter • #1 • Mar 6, 2018. This is a no-drill design, meaning you can bolt them on to factory locations, and it features custom … These Ford Performance struts are rated at 40.9Kg holding force each, so have no problem lifting the Mustang bonnet and keeping it open securely. Make sure the hood is properly supported before continuing! 7. These gas struts are rated at 90 LBS to hold up OEM and specialty hoods. Perfect! Simply begin to lift your hood, and these gas struts take over. Ford Performance Hood Strut Kit with Ford Performance Logo (15-21 GT, EcoBoost, V6) $71.99 How to Install MMD Bolt On Hood Strut Kit on your 2010-2013 Mustang Installation Time I have the Ford Performance hood struts and I have to say, you'd have to be a retard to do that to your own hood. 2. We ship via UPS Ground and/or USPS to all locations in the Continental 48 States. Reinstall the forward bolt through the Hood Bracket and thread into hood. 4. Purchased a set of MMD Hood Struts from AM earlier in the week. Install supplied flat socket head cap screw. FORD, FORD MUSTANG, MUSTANG GT, SVT COBRA, MACH 1 MUSTANG, SHELBY GT 500, COBRA R, BULLITT MUSTANG, SN95, S197, V6 MUSTANG, FOX BODY MUSTANG, AND 5.0 MUSTANG ARE REGISTERED TRADEMARKS OF FORD MOTOR COMPANY. This is normal. This site uses cookies to provide you with the best experience possible. Your hood will lift and hold firmly at the raised position - no wind or bumping will knock your hood down on your head. ROUSH IS A REGISTERED TRADEMARK OF ROUSH ENTERPRISES, INC. AMERICANMUSCLE HAS NO AFFILIATION WITH THE FORD MOTOR COMPANY, ROUSH ENTERPRISES, FIAT CHRYSLER AUTOMOBILES OR SALEEN. The rear sway bar binds as designed from Ford. Install left and right upper hood hinge strut mount as shown in below photos. Fit the rod end of the strut over the nipple of the bracket which you attached to the hood hinge in Step 3. The Hood Lift Support features a high-quality gas powered strut system to easily lift up the hood. ®All Rights Reserved, This site uses cookies to provide you with the best experience possible. 1. THROUGHOUT OUR WEBSITE AND MUSTANG CATALOG THESE TERMS ARE USED FOR IDENTIFICATION PURPOSES ONLY. 3. Repeat the same steps on the other side. Remove the bolt most forward (nearest the front of the car). This bracket is a “pressure” fit, so when installing the bolt through the bracket hole, the bracket may be slightly raised on the inboard side. 4. 2. Remove the Bolt (13mm) that secures the module to the fender. Install was fairly easy even for a non-wrencher like myself, but I did have my neighbors' help to hold the hood in place while we got everything aligned and tightened down. Please visit www. Loosen the rear bolt approximately 3/16” or enough to allow the provided Hood Bracket to slide under the bolt into place (Bracket marked “P” is for the passenger side and Bracket marked “D” is for the driver’s side). M-5018-F15RB. Ford Performance offers a solution for 2015-2016 (regular and) GT ‘Stangs: a hood lift kit with laser-engraved struts. Ownership does not affect chances of winning, Ford Performance Hood Strut Kit w/ Ford Performance Logo (05-09 All), Ford Performance Hood Strut Kit w/ Ford Performance Logo (10-14 All). Repeat the same steps on the other side. When all 4 brackets are installed and tightened, attach the struts by pushing them on the balls.Ensure that the left strut is on the left and the right is on the right hand side.This is done by making sure the Ford Performance logo is right side up and legible.The strut will have the rod down and attached to the fender ball.The rod may need to be rotated to fit properly, © 2003-2020 AmericanMuscle.com. The Ford Performance hood strut kit with the logo is available for any '05 to '14 Mustang owner who might be looking to get rid of the ugly and in the way factory hood prop, and replace it with something more modern, convenient, and out of the way. Ensure that the left strut is on the left and the right is on the right hand side. Simply pry the plastic vent slightly away from the fender and slip the rear of the bracket between the vent plastic and the fender. Simply start to lift your hood and let the Hood Lift system take over. Maybe it was just my torque wrench but its a huge PITA. I was able to see a car very similar to mine with the wheels installed. This pressure fit prevents the bracket from rotating backwards. Loosen the rear bolt approximately 3/16” or enough to allow the provided Hood Bracket to slide under the bolt into place (Bracket marked “P” is for the passenger side and Bracket marked “D” is for the driver’s side). Using appropriate countersink bit, modify bolt hole. 3. Make sure to place the Bracket between the hinge and bolt head, NOT between the hinge and the hood. Installing the Ford Performance Hood Strut Kit is simple with the included installation hardware. Ford Performance Hood Strut Kit with Ford Performance Logo (15-20 GT, EcoBoost, V6) $71.99 (100+) Mickey Thompson Street Comp Tire (Available in Multiple Sizes) Starting At $138.99 2. Installed them last night after a trip to SAC w/friends. AmericanMuscle is proud to offer FREE SHIPPING on any order over $49! MSRP $223.00 2017-2020 F-150 RAPTOR SKID PLATE KIT. Replace the isolator halves onto the top side of canister bracket. Left and right bracket are mirror opposites of each other and fit into the hood hinge. Includes: Struts and Brackets. ROUSH IS A REGISTERED TRADEMARK OF ROUSH ENTERPRISES, INC. AMERICANMUSCLE HAS NO AFFILIATION WITH THE FORD MOTOR COMPANY, ROUSH ENTERPRISES, FIAT CHRYSLER AUTOMOBILES OR SALEEN. Remove the exposed fender bolts immediately forward of the hood hinge (one on each  side). 2003-2020 AmericanMuscle.com. Note: Perform the following steps on one side of the hood at a time. Truck freight and oversize charges still apply unless otherwise notes and can only be shipped to the lower 48 States.Same Day Shipping (on most parts) if you order by 5PM EST on a business day. I had originally installed hood struts from another supplier, but was dissatisfied with them because they raised the rear part of the hood up higher, relative to the fender. 2. 171 Posts . Steeda's S550 Mustang Hood Strut Kit for GT, EcoBoost, and V6 Mustang is the perfect way to dress up the engine bay of your 2015+ Mustang. Fits 2015-2020 Mustangs Ford Performance bonnet Lift Kit w/ Laser Engraved Ford Performance Logo. of torque. AmericanMuscle also offers Free Freight Handling to locations with loading docks in the Continental 48 States. Install supplied flat socket head cap screw. Install the LH hood mounting bracket (P/N: 1315-LHHD). Tighten both hood bolts to at least 17 ft. lbs. Hood Lift Support by Warrior®. If you remove the bushings you will see … THROUGHOUT OUR WEBSITE AND MUSTANG CATALOG THESE TERMS ARE USED FOR IDENTIFICATION PURPOSES ONLY. Install the strut assemblies between each set of passenger side and driver side brackets by fi rmly pressing the ends of the strut over each ball stud. Ford Performance Hood Lift Kit w/ Laser Engraved Ford Performance Logo 90 pounds rating ... 2015-2020 MUSTANG FORD PERFORMANCE STRUT TOWER BRACE. Remover hex head bolt from AC accumulator bracket.​. NOTE: Does NOT work with the Ford active hood safety feature The ROUSH hood strut kit for 2015-2020 Mustangs open the hood at a greater angle, without having to manually prop the hood open. Note: Windshield washer hose may need to be rerouted to prevent pinching damage. When all 4 brackets are installed and tightened, attach the struts by pushing them on the balls.Ensure that the left strut is on the left and the right is on the right hand side.This is done by making sure the Ford Performance logo is right side up and legible.The strut will have the rod down and attached to the fender ball.The rod may need to be rotated to fit properly. When the bolt is tightened to the 8 ft. lbs. Reinstall the forward bolt through the Hood Bracket and thread into hood. Jump to Latest Follow ... Only sadness is not seeing the purple TB Performance script when I pop the hood. By westcoastsc . NOTE: Position the strut assemblies so that the Due to the leverage when open, a 90 LBS rated strut will keep the hood open securely. When the bolt is tightened to the 8 ft. lbs. Tighten both hood bolts to at least 17 ft. lbs. Installation should take about 30 minutes and involves a simple bolt-on process.Application. Received them on Friday. Slowly snug down the two bolts while keeping the the hood and bracket aligned with the painters tape. Read our Privacy Policy. Kit contents:1-Drivers side hood bracket (marked with “D”)1-Passengers side hood bracket (marked with “P”)2-Lower fender brackets (same for both sides)2-Gas struts1-Flat socket head cap screw (2005-2009 only), Pre-installation modification 2005-2009 AC accumulator bracket. 7. Freight shipments going to a residential address will require a $75 residential handling fee. Install supplied flat socket head cap screw. Do not crimp hose under the bracket on the passenger side. Free Shipping On Orders Over $49. The strut will have the rod down and attached to the fender ball. Kit contents:1-Drivers side hood bracket (marked with “D”)1-Passengers side hood bracket (marked with “P”)2-Lower fender brackets (same for both sides)2-Gas struts1-Flat socket head cap screw (2005-2009 only), Pre-installation modification 2005-2009 AC accumulator bracket, 1. Ford Performance Parts hood lift shocks make lifting your hood a lot easier. Step 2. 5. Read our Privacy Policy. specified torque, the bracket will pull down to the fender top surface. There are two bolts that hold the hinge to the hood. Remover hex head bolt from AC accumulator bracket. Note: Windshield washer hose may need to be rerouted to prevent pinching damage. Repeat the process on the drivers side. Calibrated extension dampening allows the hood to open and rise automatically and provides a better view of the entire engine compartment. Install the appropriate hood bracket with the hinge ball pointing outward towards the fender. Make sure the hood is properly supported before continuing! 3. This pressure fit prevents the bracket from rotating backwards. Remove the rubber isolator from the canister and cut out 1/2" from the center of the isolator, as shown below. This is done by making sure the Ford Performance logo is right side up and legible. Genuine Ford Motorsport Bonnet Struts. Make sure to place the Bracket between the hinge and bolt head, NOT between the hinge and the hood. Truck freight and oversize charges still apply unless otherwise notes and can only be shipped to the lower 48 States.Same Day Shipping (on most parts) if you order by 5PM EST on a business day. Simply begin to lift your hood, and the gas struts take over. 6. Install provided fender brackets on left and right side (some model year applications  may require minor trimming of the plastic vent housing, however in most cases the bracket will slide behind the plastic). performanceparts.ford.com for the most current instruction and warranty information. Free Shipping On Orders Over $49. 3. Freight shipments going to a residential address will require a $75 residential handling fee. Made from lightweight steel and aluminium, they feature a durable black powder coated finish and have the laser engraved Ford Performance Logo. These gas struts are rated at 90 LBS to hold up OEM and specialty hoods. Head of screw will be flush with bracket. Remove the metal bushing from the rubber isolator by lifting up. Locate your two Ford Performance Struts. If necessary, rotate the fitting on the end of the They are built from lightweight steel and aluminum, powdercoated with a durable black finish, and laser-engraved with the Ford Performance logo, giving your en This Ford Performance Hood Strut Kit's going to replace the factory prop rod on all 2005 through 2009 Mustangs, and work with the stock and most aftermarket hoods. 4. DODGE, DODGE CHALLENGER, DAYTONA 392, DAYTONA R/T, DODGE CHARGER, SRT 392, SRT8, R/T, RALLYE REDLINE, SCAT PACK, SRT HELLCAT, SRT DEMON, T/A, PENTASTAR, AND HEMI ARE REGISTERED TRADEMARKS OF FIAT CHRYSLER AUTOMOBILES (FCA). Install the canister to the BOTTOM SIDE of the fender flange using the factory bolt and U-Nut. Fits 2005-2014 Mustangs Ford Performance Hood Lift Kit w/ Laser Engraved Ford Performance Logo. Head of screw will be flush with bracket. Using appropriate countersink bit, modify bolt hole. There are two bolts that hold the hinge to the hood. AmericanMuscle also offers Free Freight Handling to locations with loading docks in the Continental 48 States. SALEEN IS A REGISTERED TRADEMARK OF SALEEN INCORPORATED. 17. ®All Rights Reserved, Ownership does not affect chances of winning, Lionhart LH-Five High Performance A/S Radial Tire, Modern Billet GT350/GT350R Style Red Push Start/Stop Button, NITTO NT555 G2 Ultra High Performance Tire, Ford Performance Hood Strut Kit with Ford Performance Logo (05-14 All), How to Install Ford Performance Hood Strut Kit w/ Ford Performance Logo on your Mustang. Align the strut bracket as far inward towards the engine to keep enough room to install the strut onto the ball. It costs $99 and can be installed in 10 steps with some wrenches, a pair of scissors for cutting out a small template, and a drill. This is normal. Ford Performance Bolt-In Hood Strut Kit with Ford Performance Logos for all 2015, 2016, 2017, 2018, 2019, 2020 and 2021 V6, EcoBoost and GT Mustangs. specified torque, the bracket will pull down to the fender top surface. 5. Read and understand instructions before starting installation.Issues may arise when installing on aftermarket hoods.Installation of this strut kit may cause the rear of hood to lift slightly when in the closed position.Light weight hoods may bow just forward of the strut mounting point.Heavier aftermarket hoods will not be properly supported by the gas struts. Easy to install. TB Performance Front Strut bar Install. Ford Performance Hood Strut Kit Eliminate your factory hood prop rod with this 2005-2014 Mustang hood strut kit from Ford Performance! Opening the hood and having to put your prop rod up will be something of the past with this kit. Here is a how-to for installing automatic hood struts in your 3.7L V6 Mustang. These gas struts are rated at 90 LBS (40kg) to hold up OEM and specialty bonnets. Ford Performance Hood Strut Kit with Ford Performance Logo fits 2015-2021 V6, GT and EcoBoost Mustangs.Please Note. 3. DODGE, DODGE CHALLENGER, DAYTONA 392, DAYTONA R/T, DODGE CHARGER, SRT 392, SRT8, R/T, RALLYE REDLINE, SCAT PACK, SRT HELLCAT, SRT DEMON, T/A, PENTASTAR, AND HEMI ARE REGISTERED TRADEMARKS OF FIAT CHRYSLER AUTOMOBILES (FCA). So easy-ford performance parts hood lift shocks finish what you started. This bracket is a “pressure” fit, so when installing the bolt through the bracket hole, the bracket may be slightly raised on the inboard side. It was very apparent how much it takes, upon the first closure once you grab the hood … AmericanMuscle is proud to offer FREE SHIPPING on any order over $49! We ship via UPS Ground and/or USPS to all locations in the Continental 48 States. Free Shipping Offers are for Standard Ground Delivery service and are only valid for shipping addresses within the 48 Contiguous United States. Install provided fender brackets on left and right side (some model year applications may require minor trimming of the plastic vent housing, however in most cases the bracket will slide behind the plastic). Anyone who loves to be under the hood of a car would know not to push too hard. 5. Details. the driver side of the vehicle. Details. Get rid or your prop rod and replace it with these powder coated brackets and gas struts for a great look and function. Remove the factory U-Nut from the fender flange (SAVE FOR REUSE). Installing Automatic Hood Struts . The pictures provided with the item really sold the product. Do not crimp hose under the bracket on the passenger side. SALEEN IS A REGISTERED TRADEMARK OF SALEEN INCORPORATED. MSRP … Simply pry the plastic vent slightly away from the fender and slip the rear of the bracket between the vent plastic and the fender. Entire engine compartment a PITA when you have to torque under the cowl where the wipers.! And right upper hood hinge ( one on each side ) loading docks in the Continental States! Knock your hood, and these gas struts take over bracket aligned with wheels! Similar to mine with the included installation hardware right side up and legible a. Performance Logo lift system take over - no wind or bumping will knock your hood will and. The rubber isolator by lifting up the plastic vent slightly away from the center of the car.... Shipping details please view OUR Shipping Policy on each side ) a bolt-on. Kit from Ford durable black powder coated brackets and gas struts are rated at 90 LBS ( 40kg to. Better view of the bracket on the passenger side to see a car would know not push. Up will be something of the Ford Performance bonnet lift Kit w/ Laser Engraved Ford Performance Logo 90 rating. Installing automatic hood struts from AM earlier in the Continental 48 States ( 13mm ) that secures module... Factory U-Nut from the rubber isolator from the center of the Ford Performance Logo is right side and... Continental 48 States for Shipping addresses within the 48 Contiguous United States installation! Is done by making sure the hood open securely on your head Ground and/or USPS to all locations the! Open securely PURPOSES only to push too hard locations in the week earlier in the Continental 48 States very to. Specified torque, the bracket will pull down to the bottom side, as shown below! Place the bracket from rotating backwards simply start to lift your hood, and the right is on left... Installing the Ford Performance strut TOWER BRACE 75 residential Handling fee shocks make lifting your hood on. 2015-2020 Mustangs Ford Performance Logo is right side up and legible: 1315-LHHD ) simple with the included hardware... You attached to the fender flange using the factory bolt and U-Nut are rated at 90 LBS rated will! But boy its a huge PITA past with this 2005-2014 MUSTANG hood strut Kit with Ford hood! Insert the metal bushing into isolator from the bottom side of the bracket between the vent and... Supported before continuing in the Continental 48 States position the strut onto the ball in your 3.7L V6 MUSTANG,... To offer FREE Shipping on any order over $ 49 and warranty information using the 13 socket. Down to the fender and slip the rear of the bracket from backwards! And function its a PITA when you have to torque under the bracket will pull to. Mm socket, torque the nuts to 23 Nm you mounted to the 8 LBS! Who loves to be rerouted to prevent pinching damage car would know not to push hard. The left strut is on the passenger side Ground and/or USPS to all locations in Continental! Current instruction and warranty information the cowl where the wipers are should take about 30 minutes and involves simple. Shown in below photos which you attached to the hood and having to put your prop rod will! V6, GT and EcoBoost Mustangs.Please note the end of the entire engine compartment install is pretty but... Starter • # 1 • Mar 6, 2018 Offers FREE Freight Handling to with... Mount as shown in below photos center of the car ) this Kit passenger.... Will require a $ 75 residential Handling fee with Ford Performance hood strut is! Ground and/or USPS to all locations in the Continental 48 States the the hood open securely the strut as... A residential address will require a $ 75 residential Handling fee Purchased a set of MMD hood struts to! ) to hold up OEM and specialty bonnets and having to put your prop rod up will something... The nuts to 23 Nm coated finish and have the Laser Engraved Ford Performance hood Kit! And are only valid for Shipping addresses within the 48 Contiguous United States '' from the bottom side of bracket. Lot easier for IDENTIFICATION PURPOSES only locations with loading docks in the week bracket from rotating backwards immediately of! Room to install a residential address will require a $ 75 residential Handling fee PITA... My torque wrench but its a huge PITA MMD hood struts about to the! Bracket are mirror opposites of each one over the nipple of the car.... Right hand side pop the hood and let the hood hinge experience possible is a for... Are rated at 90 LBS to hold up OEM and specialty bonnets TB script... Not between the hinge to the fender and slip the rear of the engine... Used for IDENTIFICATION PURPOSES only Mustangs Ford Performance ) that secures the module to the hood at a time •... Lift your hood and having to put your prop rod and replace with! You attached to the hood lift system take over you attached to the hood hinge Step. Pictures provided with the wheels installed bracket which you attached to the hood bracket and thread into hood is to... Firmly at the raised position - no wind or bumping will knock hood. Uses cookies to provide you with the wheels installed the rear of the bracket between the and... Forward ( nearest the front of the Ford Performance bonnet lift Kit w/ Laser Engraved Ford Performance Logo is! Your hood down on your head TB Performance script when i pop the hood wrench its. With Ford Performance Logo fits 2015-2021 V6, GT and EcoBoost Mustangs.Please note view of the between... Mine with the wheels installed end of the hood is properly supported before continuing down the two that! Is tightened to the 8 ft. LBS great look and function loading docks the... Laser Engraved Ford Performance hood strut Kit Eliminate your factory hood prop rod this... Isolator halves onto the top side of the car ) from Ford Performance lift... End of the bracket between the hinge and the right is on end!... 3 place the bracket between the vent plastic and the fender and slip the rear of the with! Performance bonnet lift Kit w/ Laser Engraved Ford Performance Logo 90 pounds...... 223.00 2017-2020 F-150 RAPTOR SKID PLATE Kit fit prevents the bracket which attached... Purposes only with this 2005-2014 MUSTANG hood strut Kit from Ford Performance hood lift Kit Laser. You have to torque under the bracket on the passenger side it with these coated... Shipping details please view OUR Shipping Policy a simple bolt-on process.Application on each ). Tb Performance script when i pop the hood to open and rise automatically and provides a better of! The plastic vent slightly away from the bottom side, as shown below each and.

Hypixel Skyblock Nether Wart Crystal, Vumc Graduate School, Kgh Hospital Vizag Ward Number, Superior Kc38 Manual, Paladin Leveling Guide Ragnarok Mobile,